SharkSkin®
Solid hide.
Deck & siding stain.
An opaque exterior stain for horizontal and vertical surfaces.
Protective coatings.
Local knowledge.
KNOW THE
SURFACE.
PLAN THE
COATING.
SharkSkin® Solid Hide is a water-based exterior stain that gives decks and siding an opaque, uniform finish. Its acrylic hybrid technology combines adhesion and scuff resistance with protection against cracking, peeling and blistering.
Start with the wood, its condition and any existing finish. Our team can help you choose the preparation products and plan your deck or siding project.
Get into the details
The surface.
Identify the material, its condition and the work you’re planning.
The system.
Confirm product suitability, preparation and compatibility with our team.
The conditions.
Check the current manufacturer instructions for application, installation or maintenance requirements.
THE DETAILS.
ALL HERE.
Keep the technical information close.
Use the current manufacturer documents when planning the work.
| Manufacturer | Cloverdale Paint |
|---|---|
| Product name | SharkSkin® Solid Hide Deck & Siding Stain |
| Inventory description | CD SHARKSKIN D&S SOLID STAIN C/B (5G) |
| Unit / package | Eco 5 Gal |
| Product number | 72404-5G |
| Manufacturer product number | 72404 |
| Sheen | Pearl or Satin |
| Chemistry | Urethane |
| Coverage per coat | 240–400 ft²/gallon (5.9–9.8 m²/litre); theoretical, lower on porous or textured surfaces |
| Coats | Minimum 2; do not overbuild |
| Tack-free time | 45 minutes at 25°C and 50% relative humidity |
| Recoat time | 4–6 hours at 25°C and 50% relative humidity; longer in cool or humid conditions |
| Application temperature | Air and surface 10–30°C during application and for 6 hours afterward |
| VOC | Below 155 g/litre before thinning and colourants |
| Wet film per coat | 3.9–6.8 mils (100–170 microns) |
| Dry film per coat | 1.5–2.5 mils (38–63 microns) |
| Clean-up | Warm, soapy water |
KNOW BEFORE
YOU COAT.
Technical information.
Safety information.
Ready when you need it.
SharkSkin®
Technical data sheet – 724-series Solid Hide – Canada English
Read the full product requirements, application instructions and limitations.
Technical Data Sheet · SharkSkin® Solid Hide Deck & Siding Stain (French)
Read the full product requirements, application instructions and limitations.
72401Deep Base
Product safety and handling information.
72403White Base
Product safety and handling information.
72404Neutral Base
Product safety and handling information.
Sell Sheet (English)
Read the manufacturer’s instructions and product information.
Check the product label and current manufacturer documents for the exact component, colour and region before use.
Product images are shown for reference; packaging and options may differ from your selection.
5 Gallon3 options
Gallon3 options
Full product details, applications & manufacturer specifications
SharkSkin® Solid Hide is a water-based exterior stain that gives decks and siding an opaque, uniform finish. Its acrylic hybrid technology combines adhesion and scuff resistance with protection against cracking, peeling and blistering.
Where to use it
Use on exterior wood decks, patios, stair treads, fences, railings, soffits and trim, as well as the wood, composite, cement-board siding and cementitious surfaces listed by Cloverdale.
Preparation
The surface must be sound, clean and dry. Remove loose coatings, clean and rinse thoroughly, then scuff sand with 80–120 grit and remove the dust. New lumber must season for 2–4 weeks in normally dry conditions; pressure-treated wood needs at least 4 weeks. Follow Cloverdale’s deck-construction and priming requirements. Badly weathered or oxidized wood requires 05150 SharkSkin Adhesion Promoting Primer/Sealer. Replace rotten boards; stain will not stop rot.
Application and limitations
Apply at least two coats at the recommended spread rate without overbuilding. Maintain a wet edge. Apply only in dry conditions, with air and surface temperatures of 10–30°C maintained for at least 6 hours afterward. Avoid direct sun, relative humidity above 85%, deck temperatures above 35°C, and application within 6 hours before or after rain. Cooler temperatures, high humidity and heavy films extend drying. Use adequate ventilation and protect from freezing. Disturbing old lead paint can release toxic dust; follow the technical sheet’s lead-exposure precautions. Read the complete technical and safety sheets before use.
Recommended uses
Exterior wood decks, patios, stairs, siding, fences, railings, soffits and trim; also the composite, cement-board and cementitious surfaces listed by the manufacturer.
- Finish
Pearl or Satin
- Recoat time
4–6 hours at 25°C and 50% relative humidity; longer in cool or humid conditions
Use the sheet for your exact product code and finish. Coverage and times depend on the stated temperature, humidity, substrate and coat thickness.
- Manufacturer
- Cloverdale Paint
- Product name
- SharkSkin® Solid Hide Deck & Siding Stain
- Inventory description
- CD SHARKSKIN D&S SOLID STAIN C/B (5G)
- Unit / package
- Eco 5 Gal
- Product number
- 72404-5G
- Manufacturer product number
- 72404
- Sheen
- Pearl or Satin
- Chemistry
- Urethane
- Coverage per coat
- 240–400 ft²/gallon (5.9–9.8 m²/litre); theoretical, lower on porous or textured surfaces
- Coats
- Minimum 2; do not overbuild
- Tack-free time
- 45 minutes at 25°C and 50% relative humidity
- Recoat time
- 4–6 hours at 25°C and 50% relative humidity; longer in cool or humid conditions
- Application temperature
- Air and surface 10–30°C during application and for 6 hours afterward
- VOC
- Below 155 g/litre before thinning and colourants
- Wet film per coat
- 3.9–6.8 mils (100–170 microns)
- Dry film per coat
- 1.5–2.5 mils (38–63 microns)
- Clean-up
- Warm, soapy water
Colours &
finish options.
Start with a few colour references, then explore the full collection.
Choose from any Cloverdale colour collection.
Cloverdale Paint
Colour collection
Touch of Sun · 0852Color Is
Silent Sea · 0515Color Is
Zambia · 0963Color Is
Cyan Sky · 0681Color Is
Teen Queen · 1171Color Is
Party Time · 1109Color Is
Andes Sky · 0680Color Is
Sun's Glory · 0841Color Is- Sheen
- Pearl or Satin
Screen colours are approximate. These are collection references; colour and tint-base availability can vary by product. Confirm the colour and finish with our team and a physical sample.
Complete your project.
Companion products for the selected product and system.
SharkSkin® Wood Cleaner & Brightener
Clean and brighten wood before applying SharkSkin stain.
Use for the cleaning step; rinse and let wood dry to the chosen stain’s current requirements.
SharkSkin® Wood Stain Stripper
Remove a failing or incompatible old finish when stripping is needed.
Not every deck needs stripping. For translucent stain, prepare bare wood; brighten if stripping causes tannin darkening.
SharkSkin® Mill Glaze Remover
Treat mill glaze when it prevents stain penetration.
Only where the wood needs glaze removal; follow preparation and drying instructions.
Explore related categories
BIG PROJECT?
LET’S TALK.
Share the surface, its condition and what it needs to stand up to. We’ll help you work through the product choices and preparation.
Ask about SharkSkin® Solid Hide Deck & Siding Stain