Pre-Prime 167
A high performance, two-component chemically-cured 100% solids epoxy penetrating sealer.
Good products.
Local knowledge.
KNOW THE
PROJECT.
PLAN THE
DETAILS.
A high performance, two-component chemically-cured 100% solids epoxy penetrating sealer.
Start with the surface, the existing finish and the way the space or equipment is used. Our team can help you work through product choices and the requirements for your project.
Get into the detailsThe project.
Identify the material, its condition and the work you’re planning.
The system.
Confirm product suitability, preparation and compatibility with our team.
The conditions.
Check the current manufacturer instructions for application, installation or maintenance requirements.
THE DETAILS.
ALL HERE.
Keep the technical information close.
Use the current manufacturer documents when planning the work.
| Product type | Primer-Epoxy |
|---|---|
| Product Chemistry | Epoxy |
| Volume Solids | 100 |
| VOC content (EPA method) | 95 g/lt |
| Maximum Dry film thickness | 38 |
| Minimum Dry film thickness | 25 |
| Number of components | Multi Pack |
| Attributes | Solvent Free |
| Chemistry | Epoxy |
| Components | Two-component |
| Mixing ratio | 3 part(s) : 1 part(s) by volume |
| Pot life | 50°F (10°C) 59°F (15°C) 77°F (25°C) 6 hours 5 hours 4 hours |
| Film thickness | 1-1.5 mils (25-38 microns) dry equivalent to 1-1.5 mils (25-38 microns) wet |
| VOC | 0.79 lb/gal (95 g/lt) EPA Method 24 |
| Cleanup | Clean all equipment immediately after use with T-10 Thinner. It is good working practice to periodically flush out spray equipment during the course of the working day. Frequency of cleaning will depend upon amount sprayed, temperature and elapsed time, including any delays. All surplus material and empty containers should be disposed of in accordance with appropriate regional regulations/legislation. |
| Thinning | DO NOT THIN |
KNOW BEFORE
YOU START.
Technical information.
Safety information.
Ready when you need it.
Pre-Prime
167
TDS · Pre-Prime 167 (en_US)
Read the full product requirements, application instructions and limitations.
SDS · Pre-Prime 167 · Clear Sealer Part A (Canada, English, 2019)
Product safety and handling information.
Brochures · Pre-Prime 167 Brochure (en_US)
Read the manufacturer’s instructions and product information.
Check the product label and current manufacturer documents for the exact component, colour and region before use.
Full product details, applications & manufacturer specifications
A high performance, two-component chemically-cured 100% solids epoxy penetrating sealer.
Improves the effectiveness and efficiency of the maintenance painting process by penetrating and sealing crevices, joints, back-to-back angles of existing structures, and edges of old coatings, improving the service life of the maintenance system. Also serves to seal aged “white rusted” zinc surfaces for recoating. Recommended for rusty steel when environmental economic or safety concerns restrict abrasive blast cleaning. The extraordinary penetrating properties of Pre-Prime 167 provide a means of reinforcing rusty steel substrates, ensuring adhesion of subsequent coatings.
Equally effective at penetrating, reinforcing and sealing concrete and masonry surfaces in all industrial environments.
Recommended uses
Industrial, Commercial.
Industrial coating Priming & sealing- Finish
Semi-gloss
- Coverage
1253 sq.ft/US gallon at 1.3 mils d.f.t and stated volume solids 31.30 m²/litre at 32 microns d.f.t and stated volume solids Allow appropriate loss factors
- Application method
Airless spray, Air spray, Brush, Roller
Use the sheet for your exact product code and finish. Coverage and times depend on the stated temperature, humidity, substrate and coat thickness.
Features
- Requires a two-component mixture.
- Formulated with 100% solids.
- Product type
- Primer-Epoxy
- Product Chemistry
- Epoxy
- Volume Solids
- 100
- VOC content (EPA method)
- 95 g/lt
- Maximum Dry film thickness
- 38
- Minimum Dry film thickness
- 25
- Number of components
- Multi Pack
- Attributes
- Solvent Free
- Chemistry
- Epoxy
- Components
- Two-component
- Mixing ratio
- 3 part(s) : 1 part(s) by volume
- Pot life
- 50°F (10°C) 59°F (15°C) 77°F (25°C) 6 hours 5 hours 4 hours
- Film thickness
- 1-1.5 mils (25-38 microns) dry equivalent to 1-1.5 mils (25-38 microns) wet
- VOC
- 0.79 lb/gal (95 g/lt) EPA Method 24
- Cleanup
- Clean all equipment immediately after use with T-10 Thinner. It is good working practice to periodically flush out spray equipment during the course of the working day. Frequency of cleaning will depend upon amount sprayed, temperature and elapsed time, including any delays. All surplus material and empty containers should be disposed of in accordance with appropriate regional regulations/legislation.
- Thinning
- DO NOT THIN
Complete your project.
Companion products for the selected product and system.
Bar-Rust 235
A listed protective topcoat over Pre-Prime 167.
Select the complete system for the substrate and service. Overcoat when the sealer becomes tacky and within the technical-sheet window.
Explore related categories
BIG PROJECT?
LET’S TALK.
Share the surface, its condition and what it needs to stand up to. We’ll help you work through the product choices and preparation.
Ask about Pre-Prime 167