Intergard 740
A two component epoxy finish coat suitable for brush, roller and spray application.
Protective coatings.
Local knowledge.
KNOW THE
SURFACE.
PLAN THE
COATING.
A two component epoxy finish coat suitable for brush, roller and spray application.
Start with the surface, the existing finish and the way the space or equipment is used. Our team can help you work through product choices and the requirements for your project.
Get into the details
The surface.
Identify the material, its condition and the work you’re planning.
The system.
Confirm product suitability, preparation and compatibility with our team.
The conditions.
Check the current manufacturer instructions for application, installation or maintenance requirements.
THE DETAILS.
ALL HERE.
Keep the technical information close.
Use the current manufacturer documents when planning the work.
| Product type | Finish-Epoxy |
|---|---|
| Product Chemistry | Epoxy |
| Volume Solids | 51 |
| VOC content (EPA method) | 420 g/lt |
| Colour Options | Available on Chromascan |
| Maximum Dry film thickness | 50 |
| Minimum Dry film thickness | 50 |
| Number of components | Multi Pack |
| Chemistry | Epoxy |
| Components | Two-component |
| Mixing ratio | 4 part(s) : 1 part(s) by volume |
| Pot life | 50°F (10°C) 59°F (15°C) 77°F (25°C) 104°F (40°C) 11 hours 10 hours 8 hours 2 hours |
| Film thickness | 2 mils (50 microns) dry equivalent to 3.9 mils (98 microns) wet |
| VOC | 3.50 lb/gal (420 g/lt) EPA Method 24 344 g/kg EU Solvent Emissions Directive (Council Directive 1999/13/EC) |
| Cleanup | Clean all equipment immediately after use with International GTA822. It is good working practice to periodically flush out spray equipment during the course of the working day. Frequency of cleaning will depend upon amount sprayed, temperature and elapsed time, including any delays. |
| Thinning | International GTA220 (or Do not thin more than allowed by local environmental legislation International GTA415) |
KNOW BEFORE
YOU COAT.
Technical information.
Safety information.
Ready when you need it.
Intergard
740
TDS · Intergard 740 (en_US)
Read the full product requirements, application instructions and limitations.
MSDS · INTERGARD 740 BASE LIGHT PART A (en_CA)
Product safety and handling information.
MSDS · INTERGARD 740 BASE ULTRA DEEP PART A (en_CA)
Product safety and handling information.
MSDS · INTERGARD 740 BASE YELLOW PART A (en_CA)
Product safety and handling information.
MSDS · INTERGARD 740 PART B (en_CA)
Product safety and handling information.
MSDS · INTERGARD 740 WHITE PART A (en_CA)
Product safety and handling information.
MSDS · INTERGARD 740 BASE LIGHT PART A (en_US)
Product safety and handling information.
MSDS · INTERGARD 740 BASE ULTRA DEEP PART A (en_US)
Product safety and handling information.
MSDS · INTERGARD 740 BASE YELLOW PART A (en_US)
Product safety and handling information.
MSDS · INTERGARD 740 PART B (en_US)
Product safety and handling information.
MSDS · INTERGARD 740 WHITE PART A (en_US)
Product safety and handling information.
Proof of Performance · Infrastructure Proof of Performance (English · global)
Read the manufacturer’s instructions and product information.
Proof of Performance · Wind Power (English · global)
Read the manufacturer’s instructions and product information.
Proof of Performance · Upstream Oil & Gas Proof of Performance (English · global)
Read the manufacturer’s instructions and product information.
Check the product label and current manufacturer documents for the exact component, colour and region before use.
Full product details, applications & manufacturer specifications
A two component epoxy finish coat suitable for brush, roller and spray application.
As a tough, hard wearing finish for application over properly primed surfaces. Exhibits good abrasion resistance, and affords good protection against spills and splashes of a range of chemicals such as acids, alkalis, solvents, and salt solutions. Suitable for use in a wide range of environments including offshore structures, petrochemical facilities, bridges, pulp and paper mills, and the power industry.
Recommended uses
Exterior decks, Industrial, Commercial.
Industrial coating Marine- Finish
High Gloss
- Coverage
409 sq.ft/US gallon at 2 mils d.f.t and stated volume solids 10.20 m²/litre at 50 microns d.f.t and stated volume solids Allow appropriate loss factors
- Application method
Airless Spray, Air Spray, Brush, Roller
- Drying time
50°F (10°C): Touch dry 12 hours; hard/handle dry 40 hours 59°F (15°C): Touch dry 8 hours; hard/handle dry 30 hours 77°F (25°C): Touch dry 3 hours; hard/handle dry 16 hours 104°F (40°C): Touch dry 2 hours; hard/handle dry 11 hours
- Recoat time
50°F (10°C): Minimum 40 hours; maximum Extended¹ 59°F (15°C): Minimum 30 hours; maximum Extended¹ 77°F (25°C): Minimum 16 hours; maximum Extended¹ 104°F (40°C): Minimum 11 hours; maximum Extended¹
Use the sheet for your exact product code and finish. Coverage and times depend on the stated temperature, humidity, substrate and coat thickness.
Features
- Requires a two-component mixture.
- Product type
- Finish-Epoxy
- Product Chemistry
- Epoxy
- Volume Solids
- 51
- VOC content (EPA method)
- 420 g/lt
- Colour Options
- Available on Chromascan
- Maximum Dry film thickness
- 50
- Minimum Dry film thickness
- 50
- Number of components
- Multi Pack
- Chemistry
- Epoxy
- Components
- Two-component
- Mixing ratio
- 4 part(s) : 1 part(s) by volume
- Pot life
- 50°F (10°C) 59°F (15°C) 77°F (25°C) 104°F (40°C) 11 hours 10 hours 8 hours 2 hours
- Film thickness
- 2 mils (50 microns) dry equivalent to 3.9 mils (98 microns) wet
- VOC
- 3.50 lb/gal (420 g/lt) EPA Method 24 344 g/kg EU Solvent Emissions Directive (Council Directive 1999/13/EC)
- Cleanup
- Clean all equipment immediately after use with International GTA822. It is good working practice to periodically flush out spray equipment during the course of the working day. Frequency of cleaning will depend upon amount sprayed, temperature and elapsed time, including any delays.
- Thinning
- International GTA220 (or Do not thin more than allowed by local environmental legislation International GTA415)
Complete your project.
Companion products for the selected product and system.
Intergard 475HS
A listed epoxy intermediate for the finish system.
Confirm the complete system and recoat schedule. Intergard 475HS is not for continuous immersion.
Explore related categories
BIG PROJECT?
LET’S TALK.
Share the surface, its condition and what it needs to stand up to. We’ll help you work through the product choices and preparation.
Ask about Intergard 740