Interlac 393
A rust inhibitive primer for use over properly prepared steel. A general purpose shop primer, Interlac 393 offers low cost, easy application and low VOC.
Good products.
Local knowledge.
KNOW THE
PROJECT.
PLAN THE
DETAILS.
A rust inhibitive primer for use over properly prepared steel. A general purpose shop primer, Interlac 393 offers low cost, easy application and low VOC.
Start with the surface, the existing finish and the way the space or equipment is used. Our team can help you work through product choices and the requirements for your project.
Get into the detailsThe project.
Identify the material, its condition and the work you’re planning.
The system.
Confirm product suitability, preparation and compatibility with our team.
The conditions.
Check the current manufacturer instructions for application, installation or maintenance requirements.
THE DETAILS.
ALL HERE.
Keep the technical information close.
Use the current manufacturer documents when planning the work.
| Product type | Primer-Alkyd |
|---|---|
| Product Chemistry | Alkyd |
| Volume Solids | 55 |
| VOC content (EPA method) | 395 g/lt |
| Maximum Dry film thickness | 50 |
| Minimum Dry film thickness | 25 |
| Number of components | Single Pack |
| Chemistry | Alkyd |
| Film thickness | 1-2 mils (25-50 microns) dry equivalent to 1.8-3.6 mils (45-91 microns) wet |
| VOC | 3.29 lb/gal (395 g/lt) EPA Method 24 |
| Cleanup | Clean all equipment immediately after use with International GTA007. It is good working practice to periodically flush out spray equipment during the course of the working day. Frequency of cleaning will depend upon amount sprayed, temperature and elapsed time, including any delays. |
| Thinning | International GTA007 Do not thin more than allowed by local environmental legislation |
KNOW BEFORE
YOU START.
Technical information.
Safety information.
Ready when you need it.
Interlac
393
TDS · Interlac 393 (en_US)
Read the full product requirements, application instructions and limitations.
MSDS · INTERLAC 393 GREY (en_CA)
Product safety and handling information.
MSDS · INTERLAC 393 RED (en_CA)
Product safety and handling information.
MSDS · INTERLAC 393 GREY (en_US)
Product safety and handling information.
MSDS · INTERLAC 393 RED (en_US)
Product safety and handling information.
Check the product label and current manufacturer documents for the exact component, colour and region before use.
Full product details, applications & manufacturer specifications
A rust inhibitive primer for use over properly prepared steel. A general purpose shop primer, Interlac 393 offers low cost, easy application and low VOC.
Recommended uses
Industrial, Metal.
Industrial coating Priming & sealing- Finish
Not applicable
- Coverage
441 sq.ft/US gallon at 2 mils d.f.t and stated volume solids 11 m²/litre at 50 microns d.f.t and stated volume solids Allow appropriate loss factors
- Application method
Airless Spray, Air Spray, Brush, Roller
- Drying time
50°F (10°C): Touch dry 30 minutes; hard/handle dry 2.5 hours 59°F (15°C): Touch dry 20 minutes; hard/handle dry 2 hours 77°F (25°C): Touch dry 15 minutes; hard/handle dry 1 hour 104°F (40°C): Touch dry 5 minutes; hard/handle dry 45 minutes
- Recoat time
50°F (10°C): Minimum 1 hour; maximum Extended¹ 59°F (15°C): Minimum 1 hour; maximum Extended¹ 77°F (25°C): Minimum 45 minutes; maximum Extended¹ 104°F (40°C): Minimum 30 minutes; maximum Extended¹
Use the sheet for your exact product code and finish. Coverage and times depend on the stated temperature, humidity, substrate and coat thickness.
Features
- Manufacturer identifies a low-VOC formulation.
- Product type
- Primer-Alkyd
- Product Chemistry
- Alkyd
- Volume Solids
- 55
- VOC content (EPA method)
- 395 g/lt
- Maximum Dry film thickness
- 50
- Minimum Dry film thickness
- 25
- Number of components
- Single Pack
- Chemistry
- Alkyd
- Film thickness
- 1-2 mils (25-50 microns) dry equivalent to 1.8-3.6 mils (45-91 microns) wet
- VOC
- 3.29 lb/gal (395 g/lt) EPA Method 24
- Cleanup
- Clean all equipment immediately after use with International GTA007. It is good working practice to periodically flush out spray equipment during the course of the working day. Frequency of cleaning will depend upon amount sprayed, temperature and elapsed time, including any delays.
- Thinning
- International GTA007 Do not thin more than allowed by local environmental legislation
Explore related categories
BIG PROJECT?
LET’S TALK.
Share the surface, its condition and what it needs to stand up to. We’ll help you work through the product choices and preparation.
Ask about Interlac 393